|
|
Post by damin69 on May 19, 2013 15:42:09 GMT -6
|
|
|
|
Post by damin69 on May 12, 2013 19:52:14 GMT -6
That Might be a harder find than a Cushman.. :-(
|
|
|
|
Post by damin69 on May 11, 2013 9:18:55 GMT -6
In reply to your prob with the flashers. I believe that it takes a special flasher unit to make the LED's work properly. It is called a no load flasher and I have ordered one off Ebay to correct my LED prob. Mine flash too fast and I have not replaced the front bulbs yet. Maybe when I get the stop and turn to work at the proper rate. This is the one I used from Autozone  |
|
|
|
Post by damin69 on May 8, 2013 16:37:48 GMT -6
Well I can tell you they are all basically the same. (They all do the same thing) But they do not all look the same. I was working on my scooter and I had taken mine out of the holder to run a wire or something and for got to put it back. Well it ended up between the frame and triple tree and crushed had to replace. I went and picked up one at Autozone and wired in.
|
|
|
|
Post by damin69 on May 7, 2013 11:03:40 GMT -6
heck forget summerizing.. Take it with you... :  |
|
|
|
Post by damin69 on May 5, 2013 20:24:59 GMT -6
I have a volt Meter on every one of our Scooters. Very worth While to be able to monitor how the scooters are charging.
|
|
|
|
Post by damin69 on May 3, 2013 21:02:49 GMT -6
|
|
|
|
Post by damin69 on May 3, 2013 20:58:32 GMT -6
|
|
|
|
hard cases
by: damin69 - Apr 30, 2013 16:03:45 GMT -6
Post by damin69 on Apr 30, 2013 16:03:45 GMT -6
|
|
|
|
Post by damin69 on Apr 30, 2013 15:58:13 GMT -6
Well since you are dealing with a YY250T and they are known for less of a charging system. Going HID is One of the best options out there. You get way brighter lights than halogens and you are drawing way less than the brightest Halogen you can buy. Cruiser has posted a good link to an upgrade and if you do a bit of digging you would also find my upgrade thread also.
|
|
|
|
Post by damin69 on Apr 28, 2013 20:41:26 GMT -6
Ok did you get them going? I had this issue to begin with also. Did not really have to replace the Relay at all. Found out that Chiniese QC is not allways that good as they do not always pay attention to polarity on the bulb wires when they install them at they were backwards. I had to change the wires around on mine for the front signals. I would check that out if they still are not working for you.
|
|
|
|
Post by damin69 on Apr 28, 2013 20:34:02 GMT -6
If it is like my 2009 yes it is in the front by the horn under the front plastic. If you have small arms you can reach it without taking off the plastic. On the right side of the bike in the front.
|
|
|
|
Post by damin69 on Apr 1, 2013 8:00:42 GMT -6
Found this tip online and it saved my Life.
|
|
|
|
Post by damin69 on Mar 5, 2013 19:59:45 GMT -6
Funny this is here. I just got Word Today that for The 2 - 250 Scooters. We are going to be $280 a year.
|
|
|
|
Post by damin69 on Dec 30, 2012 15:18:20 GMT -6
Very Nice. Cool looking. Nice job that looks like it would be a lot of fun to ride.
|
|
