|
|
Post by scot on Jun 9, 2014 8:16:48 GMT -6
did you buy it from a dealer wheare they should be able to help ,there are many dealers hear in parts ,an there are some one ebay typeing in thermostat roketa 250 cc came up with 3 different ones 12.00 15.00 temp I will say 160 to 195 ok try finding dealer wear you live wich you did not mention wear you live ,you may have t wait but there should be many Chinese dealers who sell then an ship
|
|
|
|
Post by scot on Jun 9, 2014 8:05:12 GMT -6
slow trickle charge is best ,it does not make your acid boil ,like .5 but if you have 1.5 that will work to
|
|
|
|
Post by scot on Jun 9, 2014 7:58:40 GMT -6
I would just take off the front now you there couse the 2 inside for the cluster are hard to get to ,on mine the bulbs are wired in or loosks like ,you need mighty small hand to reach in there ,the 2 bolts should ratchet right out ,then there t more Philips on the inside outer edges of the cluster ,might as well check everything while your there I found many loose bots an nuts in mine ,an it brand new ,a lot of guys are replaceing with led light with less watts but more light ,not sure of the part# there are a few guys one ebay that can match them up or hear
|
|
|
|
Post by scot on Jun 8, 2014 13:51:30 GMT -6
did you see the other part I posted ,about the rear brake thanks ellpee scott
|
|
|
|
Post by scot on Jun 7, 2014 12:37:07 GMT -6
good no vibration at 60mph today I just put nose back on,an the turn signal being opposite I just swithched plugs ,works fine I just have to go right for left an left for right dededdee,for now it seems the easiest way for me then messing with takeing a lot more apart,thanks again guys should be read for weekend ride I have planned ,though I got a feeling the back trunk areas next , That turn signal part sounds odd. Are you saying turning the switch to left was causing the front right to blink, and vice versa? If so, okay, swapping the two plugs around would fix that, but then what happens to the REAR turn signals? You might now be getting front left/rear right and vice versa. Something to check. well like had said the new problem is that rear brake caliper ,being loose,its my guess its the design,as I took it apart unloosened the muffler to get to one on the main bolt s I did get that hex head off ,everything seems fine the little shock absorbers ,are what make it move a little ,I retighten all the bolts an the hex head ,its still loose but I suspect unless I have bad caliper or the pins are bad I don't know for sure but it seems ok,is yours loose a bit just move side to side a little not up an down but side to side ,i hope so thanks ellpee |
|
|
|
Post by scot on Jun 7, 2014 9:21:35 GMT -6
yes I am 6 ft 3 + with shoes on to ,I would like to do that I think I can take it to shop an see what they say ,,I notice to that rideing the scooter with old sneakers on is better then boots ,I guess the rubber from sneakers better grips the cheap want to be DiAMOND PLATEING hehehhehehe
|
|
|
|
Post by scot on Jun 7, 2014 9:20:59 GMT -6
yes I am 6 ft 3 + with shoes on to ,I would like to do that I think I can take it to shop an see what they say ,,I notice to that rideing the scooter with old sneakers on is better then boots ,I guess the rubber from sneakers better grips the cheap want to be DiAMOND PLATEING hehehhehehe
|
|
|
|
Post by scot on Jun 7, 2014 9:08:55 GMT -6
yes when I buy it one was opostite from the other ,so knew I should fix that at some point ,an so they work at same time there just opposite on the switch ,I think I got a worse problem now than that ,the turn signals work ,?rear brake caliper is loose ,an there 3/16th gap that's hex head wont turn out or in ,an now I am going to try impact wrench on it ,I am not sure if it just happen or was like it when I buy it .but it looks pretty bad that it wont last like isaid working on the thing more then rideing it
|
|
|
|
Post by scot on Jun 6, 2014 8:20:23 GMT -6
yes I would do same want to redo my whole seat ,that's a good deal I need to take out some of the seat ,I would prefur it more flat ,great price ,for me there not enough room on the seat need to slide back
|
|
|
|
Post by scot on Jun 6, 2014 8:12:52 GMT -6
thanks guys yes I had the problem one in front would blink right one in rear would blink left ,so I swithched the plugs before I put it back together ,now on the dash ,its opposite ,,but as long as I remember right is left ,an left is right they work at the same time ,it may be a the switch now .yesterday was looking at the back tighning up bolts ,I got a loose brake caliper ,I hope today it turns tighter that rear one seem poor design then again now I am seeing how the scooter itself is,theres a gap in the middle of the hex head bolt an it wont tighten anymore ,its loose but not falling off ,I may snap a pic an have the place I buy it from replace it ,so far it seems I have worked on this thing more then I ride it ,hope to get there though thanks scott
|
|
|
|
Post by scot on Jun 4, 2014 14:22:19 GMT -6
mine is the new style with the hump in it ,I took it off for an inch more room ,I wish I could have my whole seat redone couse I am so tall I feel like I wish the seat was flat or I could move back few more inches ,yes I would use vinyl repair,the newer seats some mesh that iseem to slid on very easy ,it hard to get comfy on it ,I guess need to work it
|
|
|
|
Post by scot on Jun 4, 2014 14:14:50 GMT -6
you can try ebay may have what you need an match the part up to yours,there are also some guys who sell parts hear someone will help soon ,I am not sure of the brand ,you will find it
|
|
|
|
Post by scot on Jun 4, 2014 14:00:28 GMT -6
good no vibration at 60mph today I just put nose back on,an the turn signal being opposite I just swithched plugs ,works fine I just have to go right for left an left for right dededdee,for now it seems the easiest way for me then messing with takeing a lot more apart,thanks again guys should be read for weekend ride I have planned ,though I got a feeling the back trunk areas next ,
|
|
|
|
Post by scot on Jun 4, 2014 12:46:24 GMT -6
oh yes thank you guys sorry for the ,being upset ,thanks a lot Alleyoop i know you busy >:Dyes I backed it off ,it feels better now just put the nose back on .one thing I did learn is you font have to take the black peace off too its just the red peace ,  I relize to they just wire tie the wires an cables there like in the pic ,I will retie it like that the way it was in the pic ,that was before I tighted it ,took it off for that ,god bless guys I know we all busy ,an thank you richard |
|
|
|
Post by scot on Jun 4, 2014 10:17:03 GMT -6
all is good now an tight it is that center nut ,need isay there was a lot of loose bolts there in the front end ,the problem was I tightened the brass one 1 1/4/th nut to much ,how loose should it be ,I had put like 4 quarter turns on it made it to tight,then back it off 4 quarter turns ,I did couse I felt loose ,now I suspect ,its should be somewhat loose thanks guys I know Alleyoop Ellpee flinstone thank you guys ,I know a lot to do ,hope that explain that last issues for now ,I guess i was a bit hasty ,I don't want to join another forum
|
|
