|
|
Post by richardthescooter3 on Dec 8, 2012 9:01:02 GMT -6
You may be able to re-tap those screw holes  |
|
|
|
Post by richardthescooter3 on Dec 7, 2012 17:31:44 GMT -6
fflintstone, thanks for the information, anything that can help with my mc-54-250b roketa is much appreciated, (Thanks for the posting Alleyoop) |
|
|
|
Post by richardthescooter3 on Dec 4, 2012 19:08:33 GMT -6
fflintstone, I too would like to wish you and yours a Merry Christmas  you take care my dear friend |
|
|
|
Post by richardthescooter3 on Dec 3, 2012 10:08:54 GMT -6
Nice looking scoot fflintstone |
|
|
|
Post by richardthescooter3 on Nov 30, 2012 18:47:01 GMT -6
Nice ridecheap, where did you get those mirrors (awesome looking) I'm getting ready soon to work on my scoot, got all new panels |
|
|
|
Post by richardthescooter3 on Nov 30, 2012 18:31:24 GMT -6
fflintstone, If had the money  I'd buy it |
|
|
|
Post by richardthescooter3 on Nov 30, 2012 8:22:08 GMT -6
Here you go Just below rubber hose. Attachments:
|
|
|
|
Post by richardthescooter3 on Nov 29, 2012 18:55:59 GMT -6
I would check your ground wires, check wires going into the regulator, check those connection at headlights, do you have a fuse box or just the one by the battery and starter relay? If you have fuse box check those connection under the fuse box, they are known to come loose, or not making the right contact |
|
|
|
Post by richardthescooter3 on Nov 29, 2012 11:02:13 GMT -6
Update, left scoot set awahile and she fired right up, I notice after she is running the idle does come down a little which is normal, let you know how scoot performs today  Now after moving the needle jet clip one notch leaner, going to work scoot acted up again telling it needed to be leaner, last night adjusted a/f 1/4 leaner, she fired right up and idle was good, taking it to work today let you know how it does. |
|
|
|
Post by richardthescooter3 on Nov 29, 2012 10:19:46 GMT -6
I'd check spark plug cap, make sure it didn't come off, check all the vacuum lines, check all your connections, CDI, Ignition coil, Check those intake clamps also, they can come loose |
|
|
|
Post by richardthescooter3 on Nov 29, 2012 10:04:15 GMT -6
Ok turn 1/4 leaner, but ran terrible going to work cutting out, so when I got to work I adjusted a/f to 1/2 turn richer, Alleyoop suggested moving my needle jet clip one notch leaner, so I did that this morning, took Bob's suggestion and ran scoot a long time adjusting idle and waiting see where engine adjust, finished that, but when I start scoot it seems to have a low idle and will slowly work its way up to where I had adjusted it, Is this normal?
|
|
|
|
Post by richardthescooter3 on Nov 28, 2012 8:19:18 GMT -6
Alleyoop, Scoot start a little better this morning  I turn a/f 1/4 turn clockwise last night. Should I turn that in another 1/4 or wait to see how it does tonight before coming home  I will take notice today have he performs in mid-range, (I can't get on this forum at work, so I'll go to scootdoc to let you know). |
|
|
|
Post by richardthescooter3 on Nov 27, 2012 22:32:39 GMT -6
I don't remember now why I set needle on the richest clip? should I move it? I will turn 1/4 turn leaner, and let you know how it goes. Thanks |
|
|
|
Post by richardthescooter3 on Nov 27, 2012 22:23:44 GMT -6
|
|
|
|
Post by richardthescooter3 on Nov 27, 2012 22:08:28 GMT -6
It happens when its cold (let it set over night or any length of time, it take awhile to start) When I'm trying to start scoot, I can smell gas  if that means anything, after it warmed up it usually start up pretty quick.By times I have a rough idle also. I have the a/f 2 1/2 turn out and needle jet on the richest clip. |
|
if that means anything, after it warmed up it usually start up pretty quick.By times I have a rough idle also. I have the a/f 2 1/2 turn out and needle jet on the richest clip.