|
|
Post by o0ohakko0o on Sept 19, 2015 23:09:48 GMT -6
|
|
|
|
Post by o0ohakko0o on Sept 19, 2015 18:27:17 GMT -6
Jr how can i tell if the rings are stuck or anything im unsure what im looking for etc ? Also with the valve stems after getting those 2 braces out should the stems just easily fall out mine are not just falling out about half way there getting stuck then I have to pull them really hard to get the stems completely out there also was a valve stem oil seal broken only half there and have a look at this piston looks like i need a new 1 of them also as you can see in the photo its been rubbing on something  |
|
|
|
Post by o0ohakko0o on Sept 19, 2015 1:38:35 GMT -6
here are the valves though bit hard to see but they are black full of carbon also am i meant to take them off to give a good clean out inside the casing or just the valve stems ( not sure how to get the stems out though ) on the picture below picture 1 , One seems to be smaller than the other   Also with the head off should I look at piston and rings etc ? |
|
|
|
Post by o0ohakko0o on Sept 18, 2015 20:55:35 GMT -6
Yes Jr I found that video and in the process cheers thanks
|
|
|
|
Post by o0ohakko0o on Sept 17, 2015 20:49:03 GMT -6
I will be JR looks like i have to take the flywheel off again to loosen the timing chain and i also took the engine completely off the chassis
|
|
|
|
Post by o0ohakko0o on Sept 17, 2015 12:09:01 GMT -6
Ok I'll do that today sand them down the valves but I do have to remember about the timing marks correct when the cylinder comes off because of the chain
|
|
|
|
Post by o0ohakko0o on Sept 17, 2015 10:41:56 GMT -6
Ohh sry JR sure do that's all good good blue spark .
You think I should buy a brand new cylinder head for it ?
|
|
|
|
Post by o0ohakko0o on Sept 16, 2015 22:45:52 GMT -6
Ok I'll pull the head off I ordered gaskets and I should have them tomorrow ok and with the head off do I need to open it up like open cut surgery lol
|
|
|
|
Post by o0ohakko0o on Sept 16, 2015 21:36:26 GMT -6
Yes Jr everything is correct tried fuel in the spark plug hole still nothing clean new fuel not even a hint of starting
|
|
|
|
Post by o0ohakko0o on Sept 16, 2015 19:19:13 GMT -6
Valves are set correctly no tapping sound anymore but still no luck starting with new carby (without adjusting the idle and mixture screws etc)
|
|
|
|
Post by o0ohakko0o on Sept 16, 2015 10:30:10 GMT -6
Yes JR muffler back on and I'll check the valves again today with the right tools feeler guage
|
|
|
|
Post by o0ohakko0o on Sept 16, 2015 3:45:40 GMT -6
Has not ran for like 3 yrs jr and I rewired the quad and we are in step by step process John
|
|
|
|
Post by o0ohakko0o on Sept 15, 2015 19:31:59 GMT -6
Ok just put on new carby without any adjustments but she still does not want to start ? there was a tapping sound that came on and off where the valves are while trying to start it ? you think i should again adjust the valves
|
|
|
|
Post by o0ohakko0o on Sept 15, 2015 3:29:00 GMT -6
Jr you know what I have just realised , with my new break light switch I have the wiring connected but just not put back into the break as of yet but when I push the switch in I'm not able to start the bike but when I ain't pushing the switch in the bike will turn over soooo if it's connected into the break and I have the break pulled in it ain't going to turn over ?? It's like it's in reverse if you know what I mean
|
|
|
|
Post by o0ohakko0o on Sept 14, 2015 5:02:38 GMT -6
All back together exhaust etc just waiting on a carby should have it by Thursday also ordered some gaskets incase the head has to come off
|
|
.ebay.com.au/itm/111395834360?euid=4a55c24385664be1bb74046158151638&cp=1&exe=12809&ext=32584&sojTags=exe=exe,ext=ext
