Hazard lights? By quadrunner (Read 1,083 times)

[quadrunner]

Ok I have bee poking around the scooter for quite a while and I am wondering if these things have hazard/emergency lights. Does anybody know? And if so , how do you turn them on.

[bhinch]

Welcome....I have a 2008 MC54B-250 and it does not have hazard lights. Life is Good...

[JR]

The 250A does not have hazard lights but it's easy to hook some up because I did. If you want to know how let me know.

JR

[quadrunner]

Yes I would love to know. Any help is appreciated.

[rich46]

Hi you are? I have a Jonway YY250T 2012, on the left side controls, there is a yellow switch, push
Up for hazard lights, down for normal turn signals. Hope this helps. Accidently turned mine on
Doing PDI, couldn't turn the hazard lights off till I pressed down on the signal switch. Hope this
works.

[JR]

The 250A doesn't have that switch. The models with the vertical engines do like the YY250T. To hook up a switch find one like this one on Ebay:

.ebay.com/itm/FLASHER-SWITCH-GY6-50-90-125-150-250-CHINESE-SCOOTER-/380693017553?pt=Other_Vehicle_Parts&hash=item58a31273d1&vxp=mtr" rel="nofollow" target="_blank">.ebay.com/itm/FLASHER-SWITCH-GY6-50-90-125-150-250-CHINESE-SCOOTER-/380693017553?pt=Other_Vehicle_Parts&hash=item58a31273d1&vxp=mtr

This is the one I used and I had to make my own pigtail.

You need to find 3 wires up front behind the headlight cowling. Cut a hole in the dash and put the switch where you want it. Run one wire to the gray wire on the flasher unit. Run one wire to the orange wire (left blinker) and one wire to the light blue (right blinker)

It doesn't matter which pin on the switch you put any one of these three wires, when engaged all four blinker lights will work at the same time.

JR

[alleyoop]

Here is where I put my emergency switch: and I have them on notice the two Turn signals are on the Green ones:
Alleyoop

[paulviino10]

What do you fasten the gray wire to. The power? I understand the left and right directional s.

[bhinch]

Thanks...that is my next project....you guys rock....

[JR]

Aug 11, 2013 16:24:36 GMT -6 paulviino10 said:

What do you fasten the gray wire to. The power? I understand the left and right directional s.

The emergency switch that Alley displayed in the picture is the same one that is on the ebay link.

The flasher unit is supplied with power by the black wire from the key switch. The green is ground.

The gray wire from the flasher goes to the turn signal switch on the handle bar. The flasher unit always has power but doesn't blink until you press the switch one way ort another left or right. When this happens the circuit is completed to the bulb and then it flashes.

On the switch is 3 terminals. When you hook up the orange, light blue and gray and push the switch the gray feeds or completes the circuit to both the orange and light blue wires thus all four of your blinkers along with the dash display turn signal lights will blink.

Simply splice the 3 wires off of the switch into the Gray, orange and light blue.

JR

[paulviino10]

Jr, Thank you . Paul

[ajboy123]

Got a 07 Roketa Aruba and it has hazards. Sama thing with my friends 06 Roketa Bali

[paulviino10]

Just received the switch in today's mail. Took about 2 hours to install it. Had a open area next to the ignition. Looks almost factory. Thank you Jr and Alley. Now for the wolo horn replacement, and some seat time........ Paul