Sophomore
Currently Offline
Ultimate LAD
Posts: 92 
A+'s: 1
Joined: Oct 10, 2013 15:36:57 GMT -6
|
Post by churchy on Oct 16, 2013 23:04:45 GMT -6
no i just opened it to have a look around after a bit of running
|
|
Sophomore
Currently Offline
Ultimate LAD
Posts: 92
A+'s: 1
Joined: Oct 10, 2013 15:36:57 GMT -6
|
Post by churchy on Oct 16, 2013 10:28:24 GMT -6
Also after about half hour of running the cylinder is wet and black what causes this?
|
|
Sophomore
Currently Offline
Ultimate LAD
Posts: 92
A+'s: 1
Joined: Oct 10, 2013 15:36:57 GMT -6
|
Post by churchy on Oct 16, 2013 3:52:36 GMT -6
Okai so i was running a 65main jet previous to bbk with all the worlds knowledge i wouldnt know a formula to firgure out what to up jet to. Any mods to air box or oil pump just anything i need to change with a bbk on it? and are there ruels on runnibg it in?
Much apprieciated
|
|
Sophomore
Currently Offline
Ultimate LAD
Posts: 92
A+'s: 1
Joined: Oct 10, 2013 15:36:57 GMT -6
|
Post by churchy on Oct 15, 2013 18:46:24 GMT -6
i have not re jetted, am doing so but wouldnt think this can cut engine and that is practically my carb
|
|
Sophomore
Currently Offline
Ultimate LAD
Posts: 92
A+'s: 1
Joined: Oct 10, 2013 15:36:57 GMT -6
|
Post by churchy on Oct 15, 2013 17:55:22 GMT -6
okay done all this, it now runs, exhaust is smelly, white smoke, and if i go above 20 the bike can suddenly just cut out at any point, it is like it is electric problem because all you can hear is the flywheel spinning not as if the engine bogged
|
|
Sophomore
Currently Offline
Ultimate LAD
Posts: 92
A+'s: 1
Joined: Oct 10, 2013 15:36:57 GMT -6
|
Post by churchy on Oct 15, 2013 15:49:46 GMT -6
appologies, i meant from switch the is power TO the switch but not FROM.
Alley can you shed any light on the other thread?
|
|
Sophomore
Currently Offline
Ultimate LAD
Posts: 92
A+'s: 1
Joined: Oct 10, 2013 15:36:57 GMT -6
|
Post by churchy on Oct 15, 2013 15:35:38 GMT -6
ond now will wont run again
|
|
Sophomore
Currently Offline
Ultimate LAD
Posts: 92
A+'s: 1
Joined: Oct 10, 2013 15:36:57 GMT -6
|
Post by churchy on Oct 15, 2013 15:28:33 GMT -6
yup and i am not getting power to switch have ordered new one, when starter motor spins it should spin flywheel shouldnt it
|
|
Sophomore
Currently Offline
Ultimate LAD
Posts: 92
A+'s: 1
Joined: Oct 10, 2013 15:36:57 GMT -6
|
Post by churchy on Oct 15, 2013 15:24:43 GMT -6
so happy, found a mate with deep socket as to tighten spark plug, ped will now run but for seconds at a time why wont it stay running
|
|
Sophomore
Currently Offline
Ultimate LAD
Posts: 92
A+'s: 1
Joined: Oct 10, 2013 15:36:57 GMT -6
|
Post by churchy on Oct 15, 2013 10:18:42 GMT -6
okai okai, so i put new cyllinder kit on new spark pulug and, nothing  spark plug pressed against engine and i can ee the spark, if i crank it over i can smell petrol and i did it with cyllinder head off and i could see vapour come out, wondering if tightness of spark plug could be an issue i dont have a proper plug tool so have to make do with hands, could that stop it running? |
|
Sophomore
Currently Offline
Ultimate LAD
Posts: 92
A+'s: 1
Joined: Oct 10, 2013 15:36:57 GMT -6
|
Post by churchy on Oct 15, 2013 6:10:36 GMT -6
are you joking me alleyoop you have not been helpful, 'its obvious what the problem is' i have said more than once it is not the fuse
|
|
Sophomore
Currently Offline
Ultimate LAD
Posts: 92
A+'s: 1
Joined: Oct 10, 2013 15:36:57 GMT -6
|
Post by churchy on Oct 14, 2013 19:49:18 GMT -6
alleyoop you have a serious capslock issue, ought to get it seen to
|
|
Sophomore
Currently Offline
Ultimate LAD
Posts: 92
A+'s: 1
Joined: Oct 10, 2013 15:36:57 GMT -6
|
Post by churchy on Oct 14, 2013 18:14:17 GMT -6
|
|
Sophomore
Currently Offline
Ultimate LAD
Posts: 92
A+'s: 1
Joined: Oct 10, 2013 15:36:57 GMT -6
|
Post by churchy on Oct 14, 2013 17:03:51 GMT -6
ok, new cyllinder kit comes tomoz, sucks that i have college-might bunk of, ordered an upgrade on the street race to stage race 70 kit, makes 14hp out of the box  . is there any pproberbility that it was something other than the old cyllinder causing it not to run, just to brace myself for any let downs tomoz, there was spark when held against engine and there was defo fuel getting into cylinder |
|
Sophomore
Currently Offline
Ultimate LAD
Posts: 92
A+'s: 1
Joined: Oct 10, 2013 15:36:57 GMT -6
|
Post by churchy on Oct 13, 2013 11:30:33 GMT -6
im confident its a good fuse but i dont see haow id be able to once its in
|
|
