|
|
No fire
by: alleyoop - Jun 20, 2014 12:42:33 GMT -6
Post by alleyoop on Jun 20, 2014 12:42:33 GMT -6
With Key on he is sending 12v to the COIL, remember he has a TCI.
|
|
|
|
Post by alleyoop on Jun 20, 2014 12:35:36 GMT -6
HAHAHAHA, well there should be a STEENKING one there and if missing that is your problem that is what seals it so it does not leak.  Alleyoop |
|
|
|
Post by alleyoop on Jun 20, 2014 12:33:10 GMT -6
JR when he comes on I am sure will give you some suggestions He is the electrical guru on these scoots.
Alleyoop
|
|
|
|
Post by alleyoop on Jun 20, 2014 12:29:52 GMT -6
Sounds like your Regulator/Rectifier is shot.
Alleyoop
|
|
|
|
Post by alleyoop on Jun 20, 2014 12:28:14 GMT -6
I think you did not put it down far enough and you "C" clamp is in the wrong slot on the ENRICHER. Here is a pic of where the "C" clamp should be and it should be even with the top of the bore. Alleyoop  |
|
|
|
No fire
by: alleyoop - Jun 19, 2014 19:45:07 GMT -6
Post by alleyoop on Jun 19, 2014 19:45:07 GMT -6
Need some pictures BRO,
|
|
|
|
Post by alleyoop on Jun 19, 2014 19:42:44 GMT -6
I pointed to the ones that MUST BE ATTACHED those are the main ones. The other hose on the top just goes to the top of the tank as a VENT. Alleyoop #1, #2, #3 have to be connected Otherwise no gas to the carb. And that white plastic SHOULD HAVE GAS IN IT Because from there is where it flows to the carb or to the Fuel Filter and then to the CARB. IF #3 the VACUUM HOSE from the INTAKE MANIFOLD to the PUMP is NOT connected or has rips in it then NO GAS to the WHITE PLASTIC CONTAINER.  |
|
|
|
Post by alleyoop on Jun 19, 2014 19:37:48 GMT -6
Well it appears that is a overflow and vent for the tank. Here is the diagarm for the hoses so the important one is from the PUMP to the AD TANK white plastic and the one going to the carb. So make sure all the hoses are connected to that white plastic piece. So as you can see in the DIAGRAM the important one is FROM UNDER the WHITE PLASTIC PIECE which is the FUEL LINE TO THE CARB and it should FIRST GO TO A FUEL FILTER THEN TO THE CARB.  |
|
|
|
Post by alleyoop on Jun 19, 2014 18:51:09 GMT -6
Check the picture and tell me what each hose connects to.  |
|
|
|
Post by alleyoop on Jun 19, 2014 18:40:10 GMT -6
Have you checked for FUEL FLOW to the carb? Do you know which hose to take off the carb?
|
|
|
|
Post by alleyoop on Jun 19, 2014 18:30:56 GMT -6
So, I don't how which hose is the fuel hose. I did notice a few things. This wire looks frayed (grounding wire?) tinypic.com/r/502vk9/8Yes and it is taped at the end, Fix that wire to ground.
connects to this (seems like just a nut on the frame) tinypic.com/r/2lbyvtd/8these two hoses somehow became disconnected (maybe when I was looking for the fuel ratio screw) tinypic.com/r/k06cjr/8That looks like just the CARB DRAIN HOSE it should be connected to the bottom of the carb.
and this one which is connected to the mounted white box (not sure what it is) tinypic.com/r/6xsvtz/8THIS ONE I Have no idea unless you can tell me where the other end is connected to and a pic of the area around there. Has to be a connector OPEN someplace.
Well the MECHANIC that DID NOT FIX IT it said he tested for spark, I would not believe a thing he said. |
|
|
|
Post by alleyoop on Jun 19, 2014 17:34:14 GMT -6
Ok, Lets check if fuel is flowing to the carb Take the FUEL HOSE OFF the carb and put it in a cup and crank it a few times FUEL SHOULD FLOW into the cup. Then put the FUEL HOSE BACK ON THE CARB.
IF fuel flows into the CUP then we need to check if YOU ARE GETTING SPARK.
Do you know how to test that?
Alleyoop
|
|
|
|
No fire
by: alleyoop - Jun 19, 2014 17:18:10 GMT -6
Post by alleyoop on Jun 19, 2014 17:18:10 GMT -6
Then plug it back in because otherwise you will not be able to kill the motor, or you can pull the BOOT CAP off the plug to kill it. Then your problem is the killswitchs
Alleyoop
|
|
|
|
Post by alleyoop on Jun 19, 2014 16:46:47 GMT -6
Ok, Video works good. On the Carb on the Side Left side see if you have a Fuel Ratio Mixture Screw. Look at this picture and see the Fuel Ratio Screw. Turn that CLOCKWISE until it stops and then TURN IT COUNTER CLOCKWISE 2 1/2 turns see if it then ATTEMPTS to start.  |
|
|
|
Post by alleyoop on Jun 19, 2014 16:23:20 GMT -6
To post pictures use this it is free and easy; Alleyoop 1. Click on this link: tinypic.com/index.php2. Click on Browse, that will link to your computer. 3. Find what you want to load. 3. Click on the name of the picture 4. Click on OPEN 5. Click on UPLOAD 6. Click on the LINK that starts with IMG. 7. RIGHT CLICK and CLICK on COPY 8. THEN Come here to your THREAD ON DOC. 9. RIGHT CLICK and CLICK ON PASTE. |
|
..BAD TO THE BONE..
