New Student
Currently Offline
Posts: 7
A+'s: 0
Joined: Aug 25, 2013 19:38:17 GMT -6
|
thermostat
by: rideon1946 - Nov 30, 2013 21:08:39 GMT -6
Post by rideon1946 on Nov 30, 2013 21:08:39 GMT -6
My ?Is their any difference in a Thermostat for the 257 linhai engine and the 244 honda clone engine?Will either thermostat work in ether engine.Thanks for any help ahead time.
|
|
New Student
Currently Offline
Posts: 7
A+'s: 0
Joined: Aug 25, 2013 19:38:17 GMT -6
|
Post by rideon1946 on Nov 14, 2013 16:46:59 GMT -6
If it starts as good as you say,and runs good for awhile ,I would check coil first,then the CDI.It sounds like the coil may be going bad,but I have seen the CdI do the same thing.Good Luck.
|
|
New Student
Currently Offline
Posts: 7
A+'s: 0
Joined: Aug 25, 2013 19:38:17 GMT -6
|
Post by rideon1946 on Nov 8, 2013 11:39:47 GMT -6
Got my new CDI off of Amazon for 36.00 +4.00 shipping.Got it in today.Hooked it up,bike runs like new.What a deal.
|
|
New Student
Currently Offline
Posts: 7
A+'s: 0
Joined: Aug 25, 2013 19:38:17 GMT -6
|
Post by rideon1946 on Oct 31, 2013 8:16:20 GMT -6
Hi all,recently my cdi went bad,up till then had never had problem.Scooter ran great,257linhai engine had all kinds of power.Bought new cdi off ebay,scooter starts good now but when cold moter will backfire .After it warms up a little it runs better but no power at all,acts like it is out of time.On my old cdi,it had the #0607 and that is all,the new one does not have those #s.It makes me think I bought the wrong cdi.Oh yea when I ride it now and let off the gas it starts backfireing until I give it gas again.Hope some one might be able to help me out on this one.Thanks for any help.
|
|
New Student
Currently Offline
Posts: 7
A+'s: 0
Joined: Aug 25, 2013 19:38:17 GMT -6
|
Post by rideon1946 on Sept 16, 2013 11:41:59 GMT -6
Hi all,I have no spark at plug,have checked coil by replaceing,also replaced CDI,went over all the connection's,only has 3 fuses,all good,checked the stator to see if it was grounded to motor,not grounded to motor.I am thinking it is a bad pick up coil.It ohmed 203 ohms from blue wire to yellow.That sounds high but dont know what it should read.If anyone out thier knows it would be a great help to me.Also what voltage should I receive through the PU coil wires while the motor is turning over.Thanks for any help.
|
|
New Student
Currently Offline
Posts: 7
A+'s: 0
Joined: Aug 25, 2013 19:38:17 GMT -6
|
coil wires
by: rideon1946 - Aug 27, 2013 6:45:27 GMT -6
Post by rideon1946 on Aug 27, 2013 6:45:27 GMT -6
Thanks John' No not yet will today,in the meantime if anyone out their knows the answer it sure would help me out
|
|
New Student
Currently Offline
Posts: 7
A+'s: 0
Joined: Aug 25, 2013 19:38:17 GMT -6
|
coil wires
by: rideon1946 - Aug 26, 2013 7:22:46 GMT -6
Post by rideon1946 on Aug 26, 2013 7:22:46 GMT -6
Hi all,I have a express md250t .It is water cooled .My problem is wiring the coil properly.It has the big coil with metal bar running through the middle.On back of coil it has a small connector and a bigger connector.I have a orange wire and a black wire that hooks to the coil but both wires have lg connectors on them.The black wire is hot when key is on.I think the orange wire comes from the CDI. I dont want to hook it up wrong,afraid I will blow the cdi box,the cdi is the 8 connector type but only has 5 wires going to it.Thanks for any help
|
|
