|
|
Post by richardthescooter3 on Nov 17, 2012 7:58:47 GMT -6
Here is a better pic  Attachments:
|
|
|
|
Post by richardthescooter3 on Nov 17, 2012 7:51:38 GMT -6
Hi Alley, The only thing that's different is the one bolt hole is cut out  if that doesn't matter then it should be good, I repaired my intake again, but it still takes a little long to start then I like. Maybe this new intake will make a difference  |
|
|
|
Post by richardthescooter3 on Nov 16, 2012 19:51:42 GMT -6
Hey Guy's & Gal's will this intake manifold fit my mc-54-250b roketa scooter alright? This is a intake for 250cc linhai/yamaha scooter 170mm. Attachments:
|
|
|
|
Post by richardthescooter3 on Nov 16, 2012 8:15:47 GMT -6
I probably put it back together wrong, but soon I'm getting front tire, so I'll watch how I put it back together the right way, thanks guy's |
|
|
|
Post by richardthescooter3 on Nov 16, 2012 7:19:57 GMT -6
robert1c, as I watch that video, I notice that the belt in the clutch is in the wrong position, at idle belt should be be fully extended to the end of clutch pulley, the clutch looks like its already open at idle.
|
|
|
|
Post by richardthescooter3 on Nov 16, 2012 6:37:42 GMT -6
Maybe dumb question, but what are special about these valve adjustment tools |
|
|
|
Post by richardthescooter3 on Nov 14, 2012 21:31:43 GMT -6
Glad you found the problem, hope your back scooting soon |
|
|
|
Post by richardthescooter3 on Nov 14, 2012 21:26:29 GMT -6
fflintstone, haven't heard from you in a long time hope all things are well with you. Good to see you still have the mc-54-250b like mine I got over 13,000 mile on mine. Just bought all new panel for mine. A winter project  |
|
|
|
Post by richardthescooter3 on Nov 14, 2012 12:05:02 GMT -6
I believe those wires come from the starter relay to back of ignition coil. Attachments:
|
|
|
|
Post by richardthescooter3 on Nov 14, 2012 8:39:32 GMT -6
The time I had trouble with my clutch (I couldn't squeeze to get belt off) after getting it off, I take it apart, even pulley too, cleaned and sanded clutch pads and greased pulley area |
|
|
|
Post by richardthescooter3 on Nov 11, 2012 19:17:12 GMT -6
Well, then maybe I was going that speed  I have a GPS, I'll try it to see my actual speed |
|
|
|
Post by richardthescooter3 on Nov 11, 2012 16:03:24 GMT -6
Would it affect the speedo gear? I'll have to take a ride and see if there is any difference since took air down to 33lbs a tire.
|
|
|
|
Post by richardthescooter3 on Nov 11, 2012 15:24:51 GMT -6
Alley, I notice when changing oil today that both tires were over inflated about 7lbs each they were 41 lbs each. I think that speedo gear only goes in one way. |
|
|
|
Post by richardthescooter3 on Nov 11, 2012 11:21:56 GMT -6
Hey Guy's & Gal's, Since I changed front bears (now) my speedometer is off, did I do something wrong? I'm like going 75-80mph and cars are passing me Attachments:
|
|
|
|
Post by richardthescooter3 on Nov 10, 2012 17:13:55 GMT -6
I agree too. That happened to me, every time the scoot stop, it would stall, (because clutch was still engaged) replaced main clutch spring, problem solved |
|
