|
|
Post by tvnacman on Jul 27, 2012 8:56:20 GMT -6
Rain! Rain! glorious RAIN!! Not only that the rain came right across the same region that just burned! CC you did it, I know you got out there and did that RAIN DANCE!! Don't know how long it'll last but it's been raining so hard that my satellite internet service went down. It is raining cats and dogs! Cool, wet rain! JR This upsets you, I would get in my birthday suite and dance around in it. John |
|
|
|
Post by tvnacman on Jul 25, 2012 19:30:36 GMT -6
I'm not sure if I'm doing something wrong but I'm not getting a reading when I check the black/brown wire. I put the red lead on the connection for that wire. Where do I connect the black lead? I know this seems rather elementary but I just want to make sure I'm not doing something wrong. Thanks. ground or neg battery . John |
|
|
|
Post by tvnacman on Jul 25, 2012 19:23:50 GMT -6
good luck JR
I'll say a prayer for you .
John
|
|
|
|
Post by tvnacman on Jul 24, 2012 19:31:11 GMT -6
both . the stator/generator is kind of stable output bases on rpm . The regulator will output dcv based on acv input and dc load any extra that would increase the dc voltage will be loaded to ground . milage has nothing to do with stator regulator or any electrical power .
John
|
|
|
|
Post by tvnacman on Jul 24, 2012 17:31:07 GMT -6
I missed this you want it without the bell ? PM me for price . John |
|
|
|
Post by tvnacman on Jul 24, 2012 17:26:58 GMT -6
|
|
|
|
Post by tvnacman on Jul 23, 2012 19:39:40 GMT -6
Will it start ? I have a clutch for it .
John
|
|
|
|
Post by tvnacman on Jul 23, 2012 10:26:08 GMT -6
Open the cvt cover and remove the belt. See if that frees things up.
I have 12 g rollers
John
|
|
|
|
Post by tvnacman on Jul 23, 2012 9:24:16 GMT -6
|
|
|
|
Post by tvnacman on Jul 22, 2012 19:48:25 GMT -6
Yes JR , your correct in all stated above . I'm sure under the circumstance that the exact replacement part can not be found at the moment . A Y would be better than a T , I belive you would get by with either . Yes any hi or bumps in the surface area of air flow will have an effect . My question to you is 30mm carb, was the intake made the way it is for a reason . I know polishing and porting will aid in air flow/movement .
John
|
|
|
|
Post by tvnacman on Jul 22, 2012 18:47:11 GMT -6
so go with larger diameter hose , good vacuume and all will be fine .
John
|
|
|
|
Post by tvnacman on Jul 22, 2012 13:45:57 GMT -6
The job sounds very hard, many are intimadated. I was the first go round.
John
|
|
|
|
Stumped
by: tvnacman - Jul 22, 2012 13:42:42 GMT -6
Post by tvnacman on Jul 22, 2012 13:42:42 GMT -6
You were close
John
|
|
|
|
Post by tvnacman on Jul 22, 2012 6:43:33 GMT -6
Bobby what did it cost ?
John
|
|
|
|
Post by tvnacman on Jul 22, 2012 6:42:02 GMT -6
|
|
