New Student
Currently Offline
Posts: 10 
A+'s: 0
Joined: Apr 15, 2014 7:35:21 GMT -6
|
Post by ganeca on Jun 11, 2014 0:16:17 GMT -6
Thank you. Mine was clogged.
|
|
New Student
Currently Offline
Posts: 10
A+'s: 0
Joined: Apr 15, 2014 7:35:21 GMT -6
|
Post by ganeca on Jun 10, 2014 11:40:03 GMT -6
Today i bought a new thermostat and mounted it. I noticed that the temp gauge showed one section below the center. I took it for a drive and the sensor showed exact center, but when i leave it to idle i drops one section down. Is this a problem. And one last question. On the thermostat case next to the temp sensor, there is a small hose. What does it do and where does it go. Thank you all for your replies.
|
|
New Student
Currently Offline
Posts: 10
A+'s: 0
Joined: Apr 15, 2014 7:35:21 GMT -6
|
Post by ganeca on Jun 9, 2014 2:20:35 GMT -6
Most vendors do not ship outside of US, or if they do, the shipping cost is 3 times the thermostat. What is the temperature the thermostat starts to open and when it is fully open?
|
|
New Student
Currently Offline
Posts: 10
A+'s: 0
Joined: Apr 15, 2014 7:35:21 GMT -6
|
Post by ganeca on Jun 7, 2014 2:58:30 GMT -6
I have the 244 vertical honda clone
|
|
New Student
Currently Offline
Posts: 10
A+'s: 0
Joined: Apr 15, 2014 7:35:21 GMT -6
|
Post by ganeca on Jun 3, 2014 10:36:20 GMT -6
Hi,
yesterday the thermostat of my Jonway 250cc got stuck. I dissasembled it and i am looking for a replacement now. Does anybody know what brand thermostat will fit and what should be the opening degrees. Thank you in advance.
|
|
New Student
Currently Offline
Posts: 10
A+'s: 0
Joined: Apr 15, 2014 7:35:21 GMT -6
|
Post by ganeca on May 22, 2014 0:31:13 GMT -6
I isolated the plugs to the sensor, and today is welding day.
|
|
New Student
Currently Offline
Posts: 10
A+'s: 0
Joined: Apr 15, 2014 7:35:21 GMT -6
|
Post by ganeca on May 21, 2014 12:55:56 GMT -6
Found the issue. The metal frame holding the radiator and fan was broken on the right side ( bad welding) and the whole unit was moving back and forth. The lower cable going in to the fan sensor was touching the metal spring shield of the cooler hose a made a short circuit. Tomorrow i will check all the fuses just in case. Thank you all for the help  |
|
New Student
Currently Offline
Posts: 10
A+'s: 0
Joined: Apr 15, 2014 7:35:21 GMT -6
|
Post by ganeca on May 21, 2014 9:38:54 GMT -6
The model is Jonway Ranger 2008. I have a fuse box next to the battery.  I looks like this. There is a fuse for fan switch but the strange thing is the fan stops when the brake light fuse is removed. |
|
New Student
Currently Offline
Posts: 10
A+'s: 0
Joined: Apr 15, 2014 7:35:21 GMT -6
|
Post by ganeca on May 21, 2014 4:48:17 GMT -6
I think it is the vertical engine version.
I will check the fuse box.
Can i get to the fan wire without taking the whole scoot apart.
|
|
New Student
Currently Offline
Posts: 10
A+'s: 0
Joined: Apr 15, 2014 7:35:21 GMT -6
|
Post by ganeca on May 20, 2014 11:31:13 GMT -6
Hi, i have a Jonway 250cc. The problem is when i start up the engine everything is ok, but the moment i get ot the scoot the fan starts, when i stand up i stops. When i apply pressure to the back of the scoot it acts as a start button for the fan. It does the same thing when it is hot. Sometimes the fan swithes off when riding but vary rarely. Any ideas where to start looking for a solution. Thank you in advance |
|
