New Student
Currently Offline
Posts: 38 
A+'s: 0
Joined: Jan 29, 2014 14:39:12 GMT -6
|
charging
by: tavcor - Mar 27, 2014 13:37:06 GMT -6
Post by tavcor on Mar 27, 2014 13:37:06 GMT -6
hi guys I've got a 244 engine. last week i change my regulator because it went dead and today just to be sure i replaced my battery, but i found ever since i bought this scoot(second hand) i cant use fan hooter and lights at once. if just idle with no lights and fan hooter sounds normal. if the fan run full speed and i put the lights on fan would slow down until i put the lights off. check voltage at idle its fine 13 and up and rise if i rev. and in our country South Africa you looking for trouble if you dont put lights on during the day. Another thing I've got straight coolant in the system no mixture with water and the system would heats up every 60-70km. Can the plain coolant cause the heating problem?
|
|
New Student
Currently Offline
Posts: 38
A+'s: 0
Joined: Jan 29, 2014 14:39:12 GMT -6
|
overheating
by: tavcor - Mar 10, 2014 23:27:26 GMT -6
via mobile
Post by tavcor on Mar 10, 2014 23:27:26 GMT -6
Hi jburd one of our technicians in our motor workshop suggest to me putting an water and vinegar mixture in the system which I did when I got home. Rode it to work this morning which is 32km my heat gauge stayed on half so at the moment it looks like my system was partially blocked. Plan to drain it tonight when I get home and burp it will let you know what's the outcome.
|
|
New Student
Currently Offline
Posts: 38
A+'s: 0
Joined: Jan 29, 2014 14:39:12 GMT -6
|
overheating
by: tavcor - Mar 10, 2014 6:46:19 GMT -6
via mobile
Post by tavcor on Mar 10, 2014 6:46:19 GMT -6
Thanks my fan comes on waterpump works but if the pump works properly that's another story. Hope to get some guidence on this.
|
|
New Student
Currently Offline
Posts: 38
A+'s: 0
Joined: Jan 29, 2014 14:39:12 GMT -6
|
overheating
by: tavcor - Mar 9, 2014 22:58:53 GMT -6
via mobile
Post by tavcor on Mar 9, 2014 22:58:53 GMT -6
Hi guys I burp my 250 this weekend test urban stop and go everything was fine but on my way to work this morning as I hit the freeway I opened it up a little bit to about 65mph the gauge starts to climb when I reach the urban area stop and go it slowly move back to normal and my fan does come on any help out there in driving a 2008 Jonway 250cc
|
|
New Student
Currently Offline
Posts: 38
A+'s: 0
Joined: Jan 29, 2014 14:39:12 GMT -6
|
Post by tavcor on Mar 3, 2014 12:43:43 GMT -6
hi guys I've put in new clutch springs green ones and new roller weights start the scoot up idle fine but did not ride it yet but will test it tomorrow.
|
|
New Student
Currently Offline
Posts: 38
A+'s: 0
Joined: Jan 29, 2014 14:39:12 GMT -6
|
Post by tavcor on Feb 27, 2014 23:05:33 GMT -6
Allyoop the knocking noise are when the scooter are idling when I rev the shoes does grip fine. And on idling the wheel turn at a speed
|
|
New Student
Currently Offline
Posts: 38
A+'s: 0
Joined: Jan 29, 2014 14:39:12 GMT -6
|
Post by tavcor on Feb 27, 2014 23:01:27 GMT -6
Same size belt that was on the shoes gripping and hitting the bell is my main problem at the moment What exactly do you mean?? SHOES GRIPPING and HITTING THE BELL is you main problem. When you twist the throttle and at a certain rpm the CLUTCH PADS will swing out and GRAB the bell and that will in turn start to turn your wheel. So what is it doing differently?? MAYBE A VIDEO with the CVT cover off and the motor running and you giving it some throttle to see what is going on would help with what you mean. Alleyoop |
|
New Student
Currently Offline
Posts: 38
A+'s: 0
Joined: Jan 29, 2014 14:39:12 GMT -6
|
Post by tavcor on Feb 27, 2014 8:56:38 GMT -6
Same size belt that was on the shoes gripping and hitting the bell is my main problem at the moment
|
|
New Student
Currently Offline
Posts: 38
A+'s: 0
Joined: Jan 29, 2014 14:39:12 GMT -6
|
Post by tavcor on Feb 27, 2014 8:55:57 GMT -6
Same size belt that was on the shoes gripping and hitting the bell is my main problem at the moment
|
|
New Student
Currently Offline
Posts: 38
A+'s: 0
Joined: Jan 29, 2014 14:39:12 GMT -6
|
Post by tavcor on Feb 26, 2014 23:10:06 GMT -6
I've ordered some performance springs and the supplier will send me 300cc springs which they say will be more stiffer and rollers because one of them got a flat spot can the rollers be the cause of the shoes not seating properly? But like I said all my problams start after fitting a new belt
|
|
New Student
Currently Offline
Posts: 38
A+'s: 0
Joined: Jan 29, 2014 14:39:12 GMT -6
|
Post by tavcor on Feb 26, 2014 9:39:09 GMT -6
Hi allyoop one more since put a new aftermarket belt on I get vibrations from the clutch but when its on the center stand bell of its fine but now its getting worst like a knocking noise. I check the springs not broken I took them out my worry is I can clip it in with my finger I don't think it should be that easy
|
|
New Student
Currently Offline
Posts: 38
A+'s: 0
Joined: Jan 29, 2014 14:39:12 GMT -6
|
Post by tavcor on Feb 25, 2014 22:55:44 GMT -6
Hi can anyone tell if the 250cc and 150cc clutch springs are interchangeable
|
|
New Student
Currently Offline
Posts: 38
A+'s: 0
Joined: Jan 29, 2014 14:39:12 GMT -6
|
Post by tavcor on Feb 17, 2014 12:27:22 GMT -6
hi guys i think i found the problem when i put a wire inside the tank and pull the float to the right the gauges move up to its full position but as soon as i start the scoot the vibration sort of release it to the left then I'm on empty again will it help if i bend the wire that the float attached to, to the right slightly? Nightwing44 mentioned earlier about my float being position in the shallow part of the tank and need to be repositioned but I'm not sure how it should be done. i ask Nightwing44 but no respond yet any suggestions.
|
|
New Student
Currently Offline
Posts: 38
A+'s: 0
Joined: Jan 29, 2014 14:39:12 GMT -6
|
Post by tavcor on Feb 14, 2014 11:17:55 GMT -6
no Allyoop when filled up it will lay flat at empty until the tank reach about half then only will it start to register. the gauge will never go up to full even if i fill up. what wires should be swop black or the other 2 colours? i am thinking of buying a new sensor.
|
|
New Student
Currently Offline
Posts: 38
A+'s: 0
Joined: Jan 29, 2014 14:39:12 GMT -6
|
Post by tavcor on Feb 13, 2014 12:30:38 GMT -6
how do i go about reposition it Nightwing?
|
|
