Sophomore
Currently Offline
I use the KISS method?
Posts: 58
A+'s: 0
Joined: Apr 17, 2013 13:11:26 GMT -6
|
Post by rich46 on Jul 6, 2013 19:53:33 GMT -6
I had the same problem, look on the bottom on your brake levers, there is a small post not touching The lever, you will also see a small screw, back off screw slightly, push the box in, till touching the lever, tighten the screw. Hope you get the right one first. Had to lay on my back to see the underside. This worked on my YY250T.
|
|
Sophomore
Currently Offline
I use the KISS method?
Posts: 58
A+'s: 0
Joined: Apr 17, 2013 13:11:26 GMT -6
|
Post by rich46 on Jul 6, 2013 19:41:50 GMT -6
Still trying, I'm working a IPad , off a lift boat offshore, see if this works, thank you for your help! Attachments:
|
|
Sophomore
Currently Offline
I use the KISS method?
Posts: 58
A+'s: 0
Joined: Apr 17, 2013 13:11:26 GMT -6
|
Post by rich46 on Jul 4, 2013 16:14:56 GMT -6
Hi you are, found some 1/4"x20' clear hose at Lowes. Used 72" cut down the middle, on inside of curve, worked on the trunk half. Seals great , no rattle. Just have to push in slightly at the latch to
Close. Still don't understand how to post pictures? I'm still trying to post! I've read quite a few post, has helped to avoid some problems, coming up on my 1000 mile oil change and inspection.
Do keep up the good work, thanks for all your help.
|
|
Sophomore
Currently Offline
I use the KISS method?
Posts: 58
A+'s: 0
Joined: Apr 17, 2013 13:11:26 GMT -6
|
Post by rich46 on Jul 4, 2013 4:05:14 GMT -6
|
|
Sophomore
Currently Offline
I use the KISS method?
Posts: 58
A+'s: 0
Joined: Apr 17, 2013 13:11:26 GMT -6
|
Post by rich46 on Jun 23, 2013 11:20:49 GMT -6
Please understand, I have placed the hose on the inside, trunk, same as yours. It's the base I used 3/8"x 3/8"x 5" alum bars, with heavy 1/4"x1/2" rubber strip sandwiched in between. The same as yours, just user firm, hard rubber 1/2" wide, inside & outside the trunk. The trunk is Solid, no shake, no rattle. The lid with one latch, rattling away. Thinking about out checking out hardware selves, and mounting one extra latch near each rear corner. Thanks I do welcome your ideas! Now went & bought two fisheye mirrors, and mounted on inside of bike mirrors, to better see the cages on the side & slightly behind me. Has any one ever paintballed those who follow too close!!! The rains have started agin, you'll have good rides, & keep up the help! Thank you
|
|
Sophomore
Currently Offline
I use the KISS method?
Posts: 58
A+'s: 0
Joined: Apr 17, 2013 13:11:26 GMT -6
|
Post by rich46 on Jun 21, 2013 22:00:20 GMT -6
Thank you, I was in the process of trying a split hose, it is the lid. I mounted the box with 1/4" rubber, sand witched between two solid bars of aluminum, this made a very solid base with mounting contact area increased by 3/4"x 5" . I also drilled the holes thru the bars and rubber with
4 5/16" holes matching box mounting holes, also hoping the hose will weatherproof the box and lid.
Also used blue loctight on all threads.
|
|
Sophomore
Currently Offline
I use the KISS method?
Posts: 58
A+'s: 0
Joined: Apr 17, 2013 13:11:26 GMT -6
|
Post by rich46 on Jun 19, 2013 19:17:20 GMT -6
Hi y'all are! Replaced cracked variator , with a upgrade, but it had 13oz rollers, WTH, tried it.
Tops out at 65, not 70 I had before, seems smother, I believe I'll put back the original rollers,
For a while. The RPMs where a 1000 higher than normal. This is a KNM product, I liked the service,
And help videos. The lid on the trunk box rattles a lot! Is there a sealing, weather-proof gasket for
The box? I have it bolted down good with 1/4" rubber sandwiched between the cross bars, top &
Bottom.
|
|
Sophomore
Currently Offline
I use the KISS method?
Posts: 58
A+'s: 0
Joined: Apr 17, 2013 13:11:26 GMT -6
|
Post by rich46 on Jun 10, 2013 14:45:12 GMT -6
How y'all are! Enjoyed 100 mile run yesterday, did not care for the 20 minutes of rain, scoot ran great! Looking at the light filters on the vaiator cover, the wasp down here will chew up and make
Dirt dobber nest! Plan on using stainless steel mesh to cover all openings, will have to use vinyl Caulking to anchor in place & inspect regularly. I've had to this to a generator already. Have apx.
380 miles on scooter. Y'all take care.
|
|
Sophomore
Currently Offline
I use the KISS method?
Posts: 58
A+'s: 0
Joined: Apr 17, 2013 13:11:26 GMT -6
|
Post by rich46 on Jun 7, 2013 15:25:21 GMT -6
Looked at the clutch pads, only 1/2 of each pad is making contact, rough up the glaze & checked the springs, all seems well. Also changed both tire value stems with metal ones, added Dino beads. Set front @ 28#, rear @29.5#. I would like to thank all of you for help and advise!
May you roll down the road safely, and for Many miles to come! Richard
|
|
Sophomore
Currently Offline
I use the KISS method?
Posts: 58
A+'s: 0
Joined: Apr 17, 2013 13:11:26 GMT -6
|
Post by rich46 on Jun 2, 2013 21:32:49 GMT -6
Left off cover, rode 5 miles, clutch too hot to hold! Note had heavy rains earlier , road was
Washed clean & dry. Is this normal, or the bearing is bad? Still waiting for new varator.
|
|
Sophomore
Currently Offline
I use the KISS method?
Posts: 58
A+'s: 0
Joined: Apr 17, 2013 13:11:26 GMT -6
|
Post by rich46 on May 20, 2013 20:22:40 GMT -6
|
|
Sophomore
Currently Offline
I use the KISS method?
Posts: 58
A+'s: 0
Joined: Apr 17, 2013 13:11:26 GMT -6
|
Post by rich46 on May 20, 2013 17:32:45 GMT -6
Thank you very much, I was looking on the sides! Another Question , the front verator has 1/32
Cracks from center to each cooling blade , I believe this is a defect, and not just casting, is this
A disaster waiting to happen?
|
|
Sophomore
Currently Offline
I use the KISS method?
Posts: 58
A+'s: 0
Joined: Apr 17, 2013 13:11:26 GMT -6
|
Post by rich46 on May 20, 2013 12:57:57 GMT -6
Finished 160 mile, oil change, no metal in screen. Will check belt next, air filter. Still have not
Found air/fuel mix screw?
|
|
Sophomore
Currently Offline
I use the KISS method?
Posts: 58
A+'s: 0
Joined: Apr 17, 2013 13:11:26 GMT -6
|
Post by rich46 on May 20, 2013 2:48:27 GMT -6
Hi you are! Finally finished PDI! Put first 100 miles on, did some ridding after dark. How does one, adjust the headlites, on dim, I can See the road fine at 10'! Would Like to set at 100', then check out the brights! I added LEDS on the running, turn & Stop lites. Not impressed with stop lites, will have to improve.  |
|
Sophomore
Currently Offline
I use the KISS method?
Posts: 58
A+'s: 0
Joined: Apr 17, 2013 13:11:26 GMT -6
|
Post by rich46 on May 15, 2013 18:02:33 GMT -6
Under each lever is a small screw, back till loose, the black box will move. Adjust & hold, set screw
Snug up & everything is as it should be. These new scooters have been reworked by THE IDIOTS
IN CHARGE? Keep it simple, stupid! There! Thanks for the tip!
|
|
