|
|
Post by JR on Apr 28, 2012 15:59:23 GMT -6
Heck Yoster I didn't even see that either! Mine is the same screws straight across even though I don't think that would matter? Man this one has turned into a mission !
JR
|
|
Junior
Currently Offline
Posts: 152
A+'s: 0
Joined: Jul 20, 2011 17:53:15 GMT -6
|
Post by yoster on Apr 29, 2012 13:23:45 GMT -6
|
|
Junior
Currently Offline
Posts: 152
A+'s: 0
Joined: Jul 20, 2011 17:53:15 GMT -6
|
Post by yoster on Apr 29, 2012 13:27:29 GMT -6
|
|
|
|
Post by JR on Apr 29, 2012 20:11:43 GMT -6
I'm going to say this one and if you read the statement they say lots of times they only use the spring and O-rings? I'm betting the only problem is the O-ring? Can find these at your local auto parts stores. They also on this site have a number to call to ask questions so you may be able to pin your kit down to the letter by just calling. I'm still looking, this one is tough! JR |
|
Junior
Currently Offline
Posts: 152
A+'s: 0
Joined: Jul 20, 2011 17:53:15 GMT -6
|
Post by yoster on May 3, 2012 22:03:04 GMT -6
Any luck yet guys? Poor ol' Yoster is wantin' to scoot!
I pulled out the guts to replace the o-rings, bot low and behold, it doesn't use actual o-rings, but rather these proprietary rubber gasket things. Like o-rings, but not. Back to looking for a whole new master cylinder.
|
|
Sophomore
Currently Offline
Posts: 60
A+'s: 0
Joined: Jul 10, 2011 8:13:22 GMT -6
|
Post by insanetexan on May 4, 2012 6:27:46 GMT -6
|
|
Junior
Currently Offline
Posts: 152
A+'s: 0
Joined: Jul 20, 2011 17:53:15 GMT -6
|
Post by yoster on May 4, 2012 10:45:55 GMT -6
Heck, that's best I've seen so far. I might give that a shot if all else fails. Thanks!
|
|
Junior
Currently Offline
Posts: 152
A+'s: 0
Joined: Jul 20, 2011 17:53:15 GMT -6
|
Post by yoster on May 5, 2012 15:06:06 GMT -6
Hello - Does anyone know if the Honda Reflex Master Cylinder rebuild kits will work on our China scoots/ the Reflex clone? Does anyone know for certain? If so please let me know today if possible - local shop is offering to fix the thing for $30 + parts. I can get the part at the Honda shop down the road if I know it fits.
|
|
Junior
Currently Offline
Posts: 152
A+'s: 0
Joined: Jul 20, 2011 17:53:15 GMT -6
|
Post by yoster on May 9, 2012 16:53:37 GMT -6
|
|
Junior
Currently Offline
Posts: 152
A+'s: 0
Joined: Jul 20, 2011 17:53:15 GMT -6
|
Post by yoster on May 9, 2012 16:57:33 GMT -6
Ugh.. nevermind.. those look different..
|
|
|
|
Post by JR on May 9, 2012 19:33:00 GMT -6
Yoster I haven't forgot you, just haven't had any luck! I sure the heck hope one of mine never goes bad!
I do have a possible quick fix? Soak the seals in brake parts cleaner and then see if they leak, sometimes it'll revive bad seals?
JR
|
|
|
|
Post by JR on May 9, 2012 20:01:03 GMT -6
|
|
Junior
Currently Offline
Posts: 152
A+'s: 0
Joined: Jul 20, 2011 17:53:15 GMT -6
|
Post by yoster on May 9, 2012 20:47:37 GMT -6
Ahh JR, look at the screw locations on the lid.. they're in opposite corners.. not the center. That's the smaller reservoir for the 150cc scoots  |
|
|
|
Post by JR on May 9, 2012 21:05:21 GMT -6
Yoster, I just went out and measured mine and the measurements on that was very close to the same? 53mm was the same, and mine was about 62mm compared to the 66mm they listed and I don't have a clue on the 27mm measurement?
JR
|
|
Junior
Currently Offline
Posts: 152
A+'s: 0
Joined: Jul 20, 2011 17:53:15 GMT -6
|
Post by yoster on May 9, 2012 21:38:26 GMT -6
Well if you think it will work then I'm game. Does it have the correct 'brake light switch' on it? I couldn't really tell from that pic.
|
|
