New Student
Currently Offline
Posts: 28
A+'s: 0
Joined: Aug 31, 2012 17:14:47 GMT -6
|
Post by amossearan on Dec 30, 2012 12:51:23 GMT -6
valves adjusted .... still will not hold idle .... reinstalled old ignition box .... holding idle much better and is not chugging @ lower speeds ..... will tweak the fuel mix (maybe that will help)
|
|
New Student
Currently Offline
Posts: 28
A+'s: 0
Joined: Aug 31, 2012 17:14:47 GMT -6
|
Post by amossearan on Dec 29, 2012 14:46:30 GMT -6
My LinHai 260T runs out fine @ 50-65 mph .... when I decelerate for a turn or stop at light .... scooter dies. I can hit the start button, it starts up most of the time then I accelerate and it runs fine and smooth until I have to slow down to 10-15 mph .... any help is much appreciated.
Amos:)
|
|
New Student
Currently Offline
Posts: 28
A+'s: 0
Joined: Aug 31, 2012 17:14:47 GMT -6
|
Post by amossearan on Dec 8, 2012 14:23:38 GMT -6
voltage verified ... replaced stator and pu coil ..... now have spark and scooter is running .... thanks guys  |
|
New Student
Currently Offline
Posts: 28
A+'s: 0
Joined: Aug 31, 2012 17:14:47 GMT -6
|
Post by amossearan on Nov 19, 2012 10:10:44 GMT -6
I bypassed the sidekick stand .... still no spark
|
|
New Student
Currently Offline
Posts: 28
A+'s: 0
Joined: Aug 31, 2012 17:14:47 GMT -6
|
Post by amossearan on Nov 13, 2012 5:22:19 GMT -6
thanks for the info. , hmmmmm I was wondering about the sidestand cutoff possibility.... again, thanks so much for your help, it is much appreciated:)
|
|
New Student
Currently Offline
Posts: 28
A+'s: 0
Joined: Aug 31, 2012 17:14:47 GMT -6
|
Post by amossearan on Nov 12, 2012 16:29:30 GMT -6
readings using my multimeter set@ 200 ohms ...... 2.3 on the old coil and 5.6 on the new coil
|
|
New Student
Currently Offline
Posts: 28
A+'s: 0
Joined: Aug 31, 2012 17:14:47 GMT -6
|
Post by amossearan on Nov 12, 2012 15:00:29 GMT -6
could someone tell me the correct coil and pickup coil readings /values for this scooter?
|
|
New Student
Currently Offline
Posts: 28
A+'s: 0
Joined: Aug 31, 2012 17:14:47 GMT -6
|
Post by amossearan on Nov 11, 2012 18:51:59 GMT -6
Hi Guys .....
Sorry about the pic clarity ....... the colors are as follows from left to right .....
.. Black / Yellow
.. Blue
.. Green
.. Blue / Yellow
.. Red / Black
|
|
New Student
Currently Offline
Posts: 28
A+'s: 0
Joined: Aug 31, 2012 17:14:47 GMT -6
|
Post by amossearan on Nov 10, 2012 19:38:03 GMT -6
Ill check tomorrow .... Thanks |
|
New Student
Currently Offline
Posts: 28
A+'s: 0
Joined: Aug 31, 2012 17:14:47 GMT -6
|
Post by amossearan on Nov 10, 2012 16:35:14 GMT -6
send me a pm with your email and I will forward the pics ....
Thanks
Amos:)
|
|
New Student
Currently Offline
Posts: 28
A+'s: 0
Joined: Aug 31, 2012 17:14:47 GMT -6
|
Post by amossearan on Nov 10, 2012 16:20:46 GMT -6
CDI colors are ....
..Black and Yellow
..Blue
..Green
..Blue and Yellow
..Red and Black
|
|
New Student
Currently Offline
Posts: 28
A+'s: 0
Joined: Aug 31, 2012 17:14:47 GMT -6
|
Post by amossearan on Nov 10, 2012 15:59:43 GMT -6
Howdy All,
I finally received my new coil coil and am ready to proceed ..... after installing the new coil .... still no spark ..... hmmmmm
|
|
New Student
Currently Offline
Posts: 28
A+'s: 0
Joined: Aug 31, 2012 17:14:47 GMT -6
|
Post by amossearan on Oct 25, 2012 19:51:42 GMT -6
I recently replaced the CDI box , new plug , Carb adjusted, valves adjusted ... ran great for a couple of days. The unit started bogging down and stalling out .... then would run fine after sitting for 30-45 minutes. The unit turns over but there is absolutely no spark. Thanks in advance for your help. |
|
