New Student
Currently Offline
Posts: 26
A+'s: 0
Joined: Feb 7, 2014 21:49:15 GMT -6
|
Post by rp62 on Feb 24, 2014 12:24:45 GMT -6
So it is an 1P57QMJ with a 250cc CVT configuration because of the 16 in. wheels. Thank you Alleyoop!
|
|
New Student
Currently Offline
Posts: 26
A+'s: 0
Joined: Feb 7, 2014 21:49:15 GMT -6
|
Post by rp62 on Feb 23, 2014 18:06:34 GMT -6
Hi tvnacman,
The valve cover has four (4) bolts. Please see pictures posted. What can you tell about the engine?
Thanks
|
|
New Student
Currently Offline
Posts: 26
A+'s: 0
Joined: Feb 7, 2014 21:49:15 GMT -6
|
Post by rp62 on Feb 23, 2014 17:57:05 GMT -6
Alleyoop,
I would like your final comment about if this engine is a BN157QMJ.
Thank you.
|
|
New Student
Currently Offline
Posts: 26
A+'s: 0
Joined: Feb 7, 2014 21:49:15 GMT -6
|
Post by rp62 on Feb 23, 2014 15:05:09 GMT -6
Yes Alleyoop 5-3/8, my bad. Thanks!
|
|
New Student
Currently Offline
Posts: 26
A+'s: 0
Joined: Feb 7, 2014 21:49:15 GMT -6
|
Post by rp62 on Feb 23, 2014 14:00:07 GMT -6
More pictures... Attachments:
|
|
New Student
Currently Offline
Posts: 26
A+'s: 0
Joined: Feb 7, 2014 21:49:15 GMT -6
|
Post by rp62 on Feb 23, 2014 13:58:05 GMT -6
Hi guys, I took some time today to measure the CVT components and take a look at the Valve Cover. I measured the diameter of the Variator Fan, Clutch Bell and Clutch Pulley. The VF is almost 4-13/16 in. (122 mm), the CB is 5-3/8 in., and the CP is a little less than 6-1/8 in. I also checked the Belt specs which are 906-22.5-30. In reference to the Valve Cover I saw it has four (4) bolts holding it. Again, I will appreciate your comments and guidance after this info. I hope to figure it out after it. Here you have some pictures. Thank you! |
|
New Student
Currently Offline
Posts: 26
A+'s: 0
Joined: Feb 7, 2014 21:49:15 GMT -6
|
Post by rp62 on Feb 18, 2014 17:27:27 GMT -6
Thanks Alleyoop. I'll measure the Fan Variator as soon as possible. After seeing the pictures, do you still think it is a BN157QMJ engine even though it indicates 1P57QMJ?
|
|
New Student
Currently Offline
Posts: 26
A+'s: 0
Joined: Feb 7, 2014 21:49:15 GMT -6
|
Post by rp62 on Feb 16, 2014 13:21:11 GMT -6
|
|
New Student
Currently Offline
Posts: 26
A+'s: 0
Joined: Feb 7, 2014 21:49:15 GMT -6
|
Post by rp62 on Feb 16, 2014 13:18:44 GMT -6
   Hi everyone, thanks for the help. I'm sorry but I don't have an impact wrench or the tool to hold the variator in order to release the nut, so I can count the splines. However, I did was able to uncover the CVT and take the pictures attached in this and next post. I really hope it helps |
|
New Student
Currently Offline
Posts: 26
A+'s: 0
Joined: Feb 7, 2014 21:49:15 GMT -6
|
Post by rp62 on Feb 12, 2014 17:44:34 GMT -6
Thank you Alleyoop. Picture of CVT with cover removed, right?
|
|
New Student
Currently Offline
Posts: 26
A+'s: 0
Joined: Feb 7, 2014 21:49:15 GMT -6
|
Post by rp62 on Feb 11, 2014 21:38:29 GMT -6
Hi everyone,
My scooter sells in Venezuela under the brand Skygo Elegance SG150T-8, but it really is a Lifan LF150T-9R. It is equiped with a 1P57QMJ engine and rides on 16 inches wheels. I found that it is very similar to Rocketa MC-12-150 which is comercialized in the US. As a matter of fact both have the same engine.
i need to replace the clutch which started to shown signs of wear at 2.500 km, but I would like to use a better quality one and by the way replace the variator. I haven't been able to find a performance variator, it seems this engine is a rare one. In fact it looks different to most 1P57QMJ engines.
I will appreciate very much any help on this matter.
|
|
