|
|
Post by scot on Jun 2, 2014 12:36:50 GMT -6
I been rideing my scooter around town ,an like a lot of guys I have checked for loose nuts bolt etc.an seem to be getting a bit to much vibration from the left handle bar ,more then the right very noticeable at 45 to 50 mph,going to look into it further ,I knew there was a good reason to join hear ,an been busy ,has anyone had that happen ,that is one thing I have not pulled the cover on ,mabey front tire out of balance,thanks for any help guys an hope you enjoying rideing we finaly got there ,an this would be safety issue for me ,?I may be wrong if I heard someone say they are speperate on either side ,meening not one whole peace , |
|
|
|
Post by scot on Jun 2, 2014 14:23:29 GMT -6
well I guess unless you got a bent Philips like hex head to get the ignition off ,I guess I can cheack nall my wireing in front an have taken the bottom an from apart now ,I am guessing for now as its got hot something just need tighting,there is nothing easy to working on these things ,but buying the door trim kit help better easly get the parts off an warmer weather helps to ,I guess I may have it fixed now is a few days though it only took about 1 hour 30 minutes to take the front plastics off ,atleast now I can check all that stuff ,,I guess next it will be the rear they put thing thing together I think to make you take them apart to tighten them up aaaahhhhhhh,hope down the road it worth it
|
|
|
|
Post by alleyoop on Jun 2, 2014 14:33:59 GMT -6
Normally the handle bars are ONE piece so maybe the part that holds it to the tree the left side is loose or broke.
Can you move the left part of the handle bar forward and backward a little?
Alleyoop
|
|
|
|
Post by scot on Jun 2, 2014 15:39:48 GMT -6
|
|
|
|
Post by scot on Jun 2, 2014 15:49:49 GMT -6
|
|
|
|
Post by alleyoop on Jun 2, 2014 15:53:32 GMT -6
Mine Trike is just like any of the 250s and it has a plate with two hold downs on each side of the plate.  |
|
|
|
Post by scot on Jun 2, 2014 16:04:54 GMT -6
ok thanks Alleoop its one peace an it does move up an down side to side as you sit on it ,I think the 3rd pic might be the culprit though I found a lot of loose nuts on the frame to the plastics ,you were right when you said we would know them in an out ,its got the 4 bolts an one threw the center of the post,its nice to have trim tool kit help separate plastics,but getting at the 2 screws one seen in pic 6 does nothing ,? I am mystified as to whats still hold that one in pic 2 ,so tomorrow I will get at it fresh an just tighten up everything,the scooter runs great is fun so far ,the fan runs full time after warm up on hotter days I guess,i should probley just plan on working everything while I am halfway there now,replaceing the lights an so on ,no bent Philips is helping hear ,,it seems the left side more then the right so hope its mabey the combo of 2 bolts on the bracket left side ,an that center one,i guess the way the got it set up thought it was not just going to fall apart like I thought ,   comes apart a lot easyer in warm weather in the right tools ,I am sure a challenge putting back together,only one crack on that center peace wich is a  still that super glue will fix ,an time for lock tight to thanks |
|
|
|
Post by alleyoop on Jun 2, 2014 16:18:30 GMT -6
No you do not need to take that screw off you have 6 screws holding the cover down, Then pull gentle out below the key and it will come off.
It has sort of a tab that grabs underneath.
Alleyoop
|
|
|
|
Post by scot on Jun 2, 2014 16:19:47 GMT -6
yes while I can now get to everything accept the top of the bracket mystery as to getting that cover off took the 2 scews out from around ignition ,something is holding it on there strong,though it does look like I will be able to get to wrenches in there tomorrow ,  do I need to take the ignition off,i hope not ,its looks not easy ,but then when I get tired an have to give up for today it all looks hard ,an I say you di that so thank a lot though,glad to have some abilitys an help |
|
|
|
Post by scot on Jun 2, 2014 16:21:19 GMT -6
oh ok will do that look for it ,I stiil needed to take it aoprt thanks alot. yes I took them all off ,its stuck I guess I will play again tomorrow an let you know :DI just put my windshield an mirrors on sunday oh well hehehe  |
|
|
|
Post by alleyoop on Jun 2, 2014 16:22:28 GMT -6
No the ignition is on a sepreate plate under there. read my previous post the cover hooks by below where the key is.
|
|
|
|
Post by alleyoop on Jun 2, 2014 16:27:45 GMT -6
Here is mine which is just like yours after you get the 6 screws out then pull out gently by where I have it labled that has a sort of a tab grabing it. Alleyoop  |
|
|
|
Post by scot on Jun 2, 2014 16:46:06 GMT -6
No the ignition is on a sepreate plate under there. read my previous post the cover hooks by below where the key is. got it it was realey on there though I had tried them early on ,though I had to take it all apart now I can torq them down good thanks .let you know when I ride again ,probley leave it down now for about how long it takes to get the lights,there it is now easy to see it ,?think that big round nut has anything to do with it ,that center bolt is tight ,thank you   |
|
|
|
Post by alleyoop on Jun 2, 2014 16:49:00 GMT -6
Yep it could be that bolt, but now that you can see the whole thing move the handlbar and see where it has the play.
Alleyoop
|
|
|
|
Post by scot on Jun 2, 2014 16:52:56 GMT -6
will do thanks Alleyoop ,it almost acted like the post itself making me think the big nut below on the post ,
|
|
..BAD TO THE BONE..
